RIFLE CASE HOLDERS

RIFLE CASE HOLDERS Reviews & Ratings

L.E. WILSON RIFLE CASE HOLDERS

The L.E. Wilson Rifle Case Holder holds the case for trimming, primer pocket reaming, neck reaming and deburring. The L.E. Wilson Trimmer Case Holder provides the ultimate accuracy and uniformity for trimming your cases. The unique design of the case holder supports the case body, much like a chamber of a firearm. The Case Holders are precisely manufactured for consistent results and repeatability.

The FIRED Case Holders are for Neck Sized Cases. NEW Case Holders work with new, unfired brass or cases that have been full length sized. If a type isn’t specified the holder will fit both Fired, New, Neck or Full Length sized cases.

View Product
Write a review
Reviews Summary
Customers praise the L.E. Wilson rifle case holders for their precision and compatibility with the Wilson trimmer, making them essential for accurate reloading. However, some issues arise with case fit for specific calibers, leading to frustration, particularly with .308 and some resized brass. Overall, the quality and performance often outweigh the challenges experienced.
What Reviewers Are Saying
Product Quality
75%
Reviewers consistently highlight the superior quality of L.E. Wilson products, noting their precision and sturdiness, which have solidified customer loyalty over time. Many mention that these holders work flawlessly with the Wilson trimmer, delivering accurate trimming results.
Fit and Compatibility
60%
Some users experienced issues with specific calibers, particularly with .308 cases not fitting properly in the holders. It's noted that accuracy may be affected based on the brass type and condition, indicating the importance of choosing the correct holders for new versus fired brass.
Service and Support
50%
Several reviews commend Brownells' customer service, particularly in addressing fit issues. L.E. Wilson’s willingness to assist customers, even offering to alter holders at no cost, reflects well on their commitment to customer satisfaction.
User Experience and Ease of Use
55%
Many users enjoy the overall experience of using the case holders, mentioning ease of use and the effective results achieved when trimming cases. However, some concerns about snug fits leading to difficulty in removing cases post-trim were noted.
Precision and Accuracy
70%
A recurring theme is the precise trimming capabilities of the Wilson system, with users reporting consistent results down to thousandths of an inch. This precision makes it highly regarded among serious reloaders who seek accuracy in their ammunition.
1
Doesnt fit my brass
I use Peterson brass for my .308 loads. The ID of these case holders is too small, so the case neck wont extend past the end of the holder. Therefore it is useless. I have .308 holders for both new and fired brass. Neither one fits my brass. The case holders I have for the other calibers I shoot work just fine, but not the .308. LEW has offered to ream it out to fit, but I have to pay shipping both ways. I will spend the money because the trimmer itself is excellent and produces variations at or less than 0.001.
1
Frustrated
Bought the original one about a year ago, waiting for a rifle to get finished finally got my rifle she's a dream by the way. Now comes the not so good, I load 308, 223, 6.8, and various pistol calipers after my first shooting with new rifle cleaned and resized brass case goes all the way through, does not stop on shoulder as others, so I'm thinking I got a bad one it happens returned to brownells for a new one, same thing happening all over again, this time, it's not rocket scientist stick the case in the gage until it stops on shoulder set your cutter to desired length and trim not that hard. So I'm surprised that I got so lucky to get two too many out of spec maybe case gages
1
Won't Work for 30-30 with Neck Bumped up
If you bump the neck up on your 30-30 cartridges to prevent excessive stretching of the brass there isn't enough of the brass extending outside of the holder to trim Details: Using a Hornady Headspace gauge, I have found my fired brass to "Headspace" at 1.503" I set my Redding die up to keep my shoulder at 1.501" to prevent excessive stretching of the brass when resizing I have been trimming my brass to 2.030", but when I changed where my shoulder was, it seems I can no longer use the Wilson Trimmer Case Holder because the end of my brass is still inside the case holder. Historically, using the generic Redding die settings my shoulder was at 1.485". This seemed to give me enough brass outside of the case holder to trim.
1
Buy CH-308W, not this one
This holder will NOT work with fully re-sized brass.
1
Not necessary for new Lapua 6mm BR Brass
While waiting for my new 6mm BR to arrive I started tooling up and bought both of the Wilson Trimmer Holders for new and fired brass. I'm using only Lapua Brass and I quickly found out that the new brass fits better in the standard Wilson Trimmer Holder.