I already knew I wanted this stock.
I have borrowed and shot other 10-22's in this same stock with a BB. It is exactly what I wanted for my build.
Great stock
Absolutely love the rubber covered stock !! Fit & feel outstanding!!
Perfect match for my bull barrel
Looks great and feels great perfect match for my new bull barrel
All around great stock
Bought this to fit my new Mist 22 integral barrel/silencer and to give the gun a more modern look. There was a little fitting needed because the barrel was a little over .925 in diameter but just scraped it of with a sharp knife in about a minute and it fit fine. It feels great during shooting and just all around looks great, hard to beat the price too.
Great stock
Excellent stock for my 10/22 with bull barrel. Fit great, looks great, and feels even better. I love the rubber feel. It'll give you great grip when it gets wet.
Beautiful Stock Beutiful Fit
My 10/22 dropped perfectly into this stock along with the .920 bull barrel that I also purchased. Everything is a flush fit and it is a very ergonomical and ambidextrous grip.I would recommend this stock to anyone who wants something more durable and comfortable than the original stock but doesn't want to spend a fortune.
This is the perfect stock!!!
Took a few minutes to install in order to get the fit perfect, but it was well worth the time. I'm buying a Mini 14 and will certainly get the same stock for it. This stock feels incredibly smooth, yet does not slip at all in your hands, and is lighter and about 100x more durable than wood. Would love to see Hogue make it for more rifles!
Solid Stock
Bottom line is this stock is solid...The rubber is going to look the best right out of the package...A stock for a bull barrel should have a bit of a cheek riser...
Nice Stock.
This stock works perfectly for a 10/22 with a bull barrel. My only complaint is that you can see through on the sides of the receiver. Otherwise it is great!
Great Stock One Fore End Caveat
Built a 10/22 using: Timney 10/22 Drop-In Trigger Assembly 883-000-038WB -- great trigger assembly, drop in with no fitting required. The lever magazine release is a great addition, helping with making the rifle a little more ambidextrous. The spring loaded bolt release works as we are accustomed to unlike the factory release. The trigger pull is crisp and clean reminiscent of the Jewel triggers on my 700. The trigger is a vast improvement over factory. 4 stars as the pull measured 3lbs on my Lyman gauge, preferred for hunting but as it is not adjustable I don't consider this a bench rest trigger. ER Shaw Fluted 10/22 .920 Target Barrel, SS 100-004-747WB -- everything I was looking for. Looks great and shoots great. 1/2" groups at 75 yards on a 100 degree, 10 - 15 mph gusty day with 20 year old Remington Golden Bullet HP, very satisfying. The barrel dropped right into the action and was installed using the factory V-block without barrel droop. V-block barrel retaining screws screws were just snugged. Checked with a set of headspace gauges and everything was fine and good to go. A 5 star barrel for sure. Hogue 10/22 Overmolded Rifle Stock B/B Rubber Covering 408-220-100WB -- The stock I wanted was out of stock so I got this one to do the build. I am liking it. Feels good in hand and on the shoulder. Ambidextrous! Bedding was accurate and felt solid. With the action screw torqued to 18 in-lbs the Shaw barrel was dollar bill free floated from 1" behind the flutes to the muzzle. The semi-varmint fore end is a joy in hand or on a bag. 4 Stars as the fore end will flex enough to touch the barrel with moderate straight line side hand pressure, a hasty sling or tight sling. Still I may well forget about the stock I wanted that cost 2-1/2 times as much, this one shoots and feels so good. Volquartsen 10/22 Socket Head Takedown Screw 930-000-O26WB -- Comparing this screw to my factory screw it is about 2-1/2 threads shorter. However it fit this build just fine, earning it 5 Stars. It and the receiver handled 18 in-lbs of torque without problem.
