BULGE BUSTER Reviews & Ratings

Push through die adapter will quickly remove the annoying bulge rings that shell holder constrained dies simply can't reach
Bulge Buster Kit includes: extension sleeve, push through punch, catch container and complete instructions.
Use with your Lee Factory Crimp Die
Will ONLY work with these cases: 380 ACP, 10mm, 40 S&W, 41 AE (Use .40 S&W Factory Crimp Die), 45 ACP, 45 GAP, and 45 Win Mag.
The Lee Carbide Factory Crimp Die is required and must be purchased separately.
This die requires the purchase of the appropriate caliber Lee factory crimp die along with the bulge buster kit. Lee does not recommend the use of this kit on cartridges that were fired thru Glock®pistols or any other pistol that does not completely support the case head when round is chambered.

View Product

Write a review

5 Stars

60%

4 Stars

20%

3 Stars

2 Stars

1 Stars

20%

Reviews Summary

The Bulge Buster is praised for its efficiency in resizing bulged brass, with many users noting it's easy to set up and use. However, some reviewers highlight the need for additional accessories like a factory crimp die and mention a few awkward handling issues. Overall, it provides a valuable solution for reloaders dealing with bulged cases.

What Reviewers Are Saying

Ease of Use

70%

Many reviewers appreciate the Bulge Buster for being straightforward to set up and operate. Users find that it simplifies the resizing process for bulged brass, highlighting its user-friendly design.

Effectiveness

80%

The product is frequently noted for its effectiveness in resizing out-of-spec brass, allowing for improved usability in reloading. Reviewers have found that it successfully resolves issues with bulged cases, particularly from specific firearm models.

Additional Requirements

40%

Several users mention the necessity of acquiring a factory crimp die to maximize the Bulge Buster's functionality, indicating it’s not a standalone solution. This added requirement caused some disappointment among a few reviewers.

Handling and Design

30%

Some users express minor frustrations regarding the handling of the brass during the resizing process. They mention that the design could be improved for better brass capture and easier operation, indicating room for improvement.

Value for Money

60%

Reviewers commonly regard the Bulge Buster as a cost-effective solution within the reloading process, appreciating its affordability relative to its performance, especially when compared to other products.

Sort by Filter by rating

Outstanding!

Very easy to set up and use! Saved a lot of brass with this product that normally wouldve been discarded.

Works Perfectly! Precision Shooter Need

I purchased bulge buster to eliminate the bulged "brass" I had from matches and the occasional reload that failed in the chamber check gauge. My 1911s are all full custom and have custom reamed chambers. Anything out of spec isn't going through, not just from sloppy unsupported polymer chambers, but factory 1911s as well. Therefore I check every round and previously discarded a lot of brass and had to take apart a lot of reloaded ammunition. With the bulge buster you can re-size (fully) out of spec brass or fully loaded ammunition. Absolute win. What I didn't know was that carbide dies don't fully size brass, however, I'm not going to switch for pistol due to the need to lube. This device allows you to have the best of both worlds. PLEASE NOTE! You will need to purchase a Lee crimp die separately (get carbide). Because the pusher moves the brass totally through it will fully size regardless. I wish the pusher could capture the brass better, but it's not possible as it has to pass totally through the die.

Lee 45 ACP bulge buster

Purchased a Lee 45 ACP bulge buster to eliminate the random bulged "range brass" I reload. Seems Glock semi-auto's like to leave bulged cases. This is easy to set up using my Lee 45 ACP crimp die and breech lock single stage press. I always double check my reloads with my L.E.Wilson case gage to make sure they will chamber. Nice die / device to have on hand for when those pesky bulged cases show up. Lee, in my opinion, makes a great product at an affordable price. I use Lee dies exclusively for all of my pistol and revolver reloading.

Lee Bulge Buster

I just purchased a Bulge Buster,for use on my .40S&W, and .45 ACP cases. I have only processed about 25 of each caliber to initially try it out. It works great, the processed cases will drop into a EGW chamber checker, without force. My only complaint is that since the case just sits on the "ram". it is necessary to insert the case into the Lee carbide die, then use the ram to push it through. It is a bit awkward. But it seems to work very well.

Don't make the same mistake as me

I missed the bit about needing a factory crimp die, Its not as cheap or as useful as it seems. True, waiting two months for the NZ police to issue a permit didn't help my mood, suppose if you pay peanuts..