The DDM4 V7 SLW AR15 style rifle is one of the lightest, fastest-handling rifles available in the DDM4 line-up, tipping the scales at under 6 lbs. Built around a Cold Hammer Forged, 14.5 inch Lightweight profile barrel, the V7 SLW has an Extended Flash Suppressor which is pinned and welded to reach the NFA required 16 inch minimum barrel length. The mid-length gas system provides smooth and reliable cycling under any conditions and reduces both perceived recoil and wear on moving parts. A free-floating MFR 13.5 M-LOK handguard offers incredible weight savings as well as superior cooling, ergonomics, and modularity while maintaining the strength and durability expected from Daniel Defense. With the M-LOK attachment points that run along 7 positions and an uninterrupted 1913 Picatinny rail on top, the V7 SLW has plenty of room for the sights, optics, and accessories the operator may require. The independently ambi GRIP-N-RIP Charging Handle accommodates left- and right-handed shooters. This rifle also comes with the ergonomic Daniel Defense Buttstock and Pistol Grip.
FEATURES:
- LOWER RECEIVER: Mil-Spec with Enhanced Flared Magazine Well and Rear Receiver QD Swivel Attachment Point. CNC Machined of 7075-T6 Aluminum
- UPPER RECEIVER: Mil-Spec with Indexing Marks and M4 Feed Ramps. CNC Machined of 7075-T6 Aluminum
- BARREL: Chrome Moly Vanadium Steel, Cold Hammer Forged, 1:7 Twist, 14.5"" Lightweight Profile, Chrome Lined, Mil-Spec Heavy Phosphate Coated, and HP/MPI Tested
- GAS SYSTEM: Pinned Low Profile Gas Block CNC Machined of 4140 Hardened Steel and Mil-Spec Heavy Phosphate Coating, Mid-length, Direct Impingement
- MUZZLE DEVICE: Pinned and Welded Daniel Defense Flash Suppressor, Extended, 17-4 PH Stainless Steel, Salt Bath Nitride Finished
- BOLT CARRIER GROUP: M16 Profile, Mil-Spec MP tested, Chrome Lined, Properly Staked Gas Key
- BUFFER: H Buffer
- SIGHTS: Sold Separately
- HANDGUARD: Daniel Defense MFR 13.5", CNC Machined of 6061-T6 Aluminum, M-LOK Attachment, Type III Hard Coat Anodized
- CHARGING HANDLE: GRIP-N-RIP Charging Handle, Body CNC Machined of 7075-T6 Aluminum, Handles & Latch CNC Machined of 6061-T6 Aluminum, Heavy Duty Stainless Steel Roll Pins, Type III Hard Coat Anodized
- RECEIVER EXTENSION: 6-Position Mil-Spec 7075-T6 Aluminum
- BUTTSTOCK: Daniel Defense Buttstock, Glass Filled Polymer with Soft Touch Overmolding
- PISTOL GRIP: Daniel Defense Pistol Grip, Glass Filled Polymer with Soft Touch Overmolding
- Made in the USA!
SPECIFICATIONS:
- Mounting System - M-LOK
- Caliber - 5.56mm NATO
- Muzzle Thread - 1 ⁄ 2 × 28 TPI (Threads Per Inch)
- Gas System - Mid-length
- Barrel Length - 14.5"
- Barrel Profile - Lightweight
- Product Weight - 5.9
- Length - 31 1/2” – 34 ¾”
- Magazine - DD Magazine with 32-round capacity in the same size magazine as industry-standard 30-round magazines
- Case - Daniel Defense Full-Latch Impact Plastic Case
FFL Restriction
You must be 18 years of age or older to purchase rifles and shotguns, and 21 or older to purchase handguns, receivers, frames, and suppressors. Minimum age requirements may vary by state. Check your state and local laws before ordering. It is your responsibility to fully understand the laws in your area and to ensure that possession of this item would not violate any applicable state or local laws. This product must be delivered to a Federal Firearms License holder.
WARNING: Cancer & Reproductive Harm - www.P65Warnings.ca.gov
