The Strike Industries Aluminum Extended Magazine Plate for GLOCK™ G19 (9mm) was designed to provide smoother magazine reloading through a slow drag / no snag design while maintaining maximum magazine capacity. Machined from 6061-T6 aluminum, this Extended Magazine Plate (EMP) adds plus 5 9mm rounds to OEM double stack GLOCK™ G19 magazines. Following the success of our EMP systems for pistols, the form factor and unique geometric design gives a unified and aggressive aesthetic look to your GLOCK™ G19. Included is an aluminum plate which adds extra locking security. Give your GLOCK™ pistol the extra rounds it deserves with the Strike Industries Aluminum Extended Magazine Plate (EMP) for GLOCK™ G19 (9mm).
WARNING: DO NOT OVERTIGHTEN set screw when installing the aluminum locking plate. If you are unsure, please contact our customer support team or consult with your local gunsmith.
Package Contents:
- x1 Aluminum Extended Magazine Plate for GLOCK™ G19
- x1 Extended length spring
- x1 Aluminum locking plate
- x1 Aluminum locking plate set screw (M3x8mm)
- x1 Hex tool
- x1 Warning card
Product Features:
- Machined from 6061-T6 aluminum
- Plus 5 round capacity for 9mm
- Includes aluminum locking plate
- Low drag / no snag design
- Fits USPSA 140mm race division limit
- Available in anodized SI BLACKLINE, REDLINE or FDELINE colors
COMPATIBILITY:
- GLOCK™ factory OEM G19 (9mm) double stack magazines
- SI EMP Pocket Clip
Magwell: tested to work with SI magwells
NOT COMPATIBLE:
- G23 (.40 Cal)
- 10-round magazines
- ETS Magazines
NOTE: Not for sale to California, Hawaii, New York and New Jersey residents due to 10-round state laws. The checkout process will show NO shipping method available.
It is the responsibility of the customer to know and abide with local gun laws.
DISCLAIMER:
Due to numerous factors that take place during the anodization process, the color lines from batch to batch of a certain product may vary
Threaded holes located on EMP are anodizing blind holes and may not be completely covered with coating
WARNING:
DO NOT OVERTIGHTEN set screw when installing the aluminum locking plate. If you are unsure, please contact our customer support team or consult with your local gunsmith.
SI aluminum EMP was intentionally designed to be a tight fit and can damage the polymer magazine body base ears. Must be installed by a certified gunsmith only.
Use of small c-clamp (or similar tool) to gently and lightly squeeze the bottom middle of the magazine body just above the plastic locking ears where the SI aluminum EMP attaches to the magazine. Just enough so the SI aluminum EMP will slide in or out. Be careful not to bend the OEM magazine body metal liner and remove the c-clamp (or similar tool) as soon as the SI aluminum EMP is installed or removed. C-clamp or similar tool may mar/scratch magazine body surface. Please be careful and use a material to protect the magazine body surface.
DISCLAIMER:
-This product is not manufactured, authorized, endorsed, or warranted by GLOCK. GLOCK does not warrant or represent that this product is compatible with GLOCK pistols.
--“GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. and GLOCK Ges.m.b.H. Neither Strike Industries Inc. nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to advertise the sale of GLOCK pistols, parts, or components.
-CALIFORNIA PROPOSITION 65 WARNING:-
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov
Magazine Extension Restriction
Please check with your state regulations for ownership of Magazine Extensions.
WARNING: Cancer & Reproductive Harm - www.P65Warnings.ca.gov
