This video showcases the Brownells Service Kit for Remington 870, 1100 & 11-87.
This video showcases the Remington 700 Police Rifle Stock by H-S Precision.
This video provides a demonstration how to change a barrel on an AR-15 or M-16.
This video segment is a description of the Mesa Tactical Products Rem 870/1100/11-87 Receiver Mount Sling Attachment.
This video segment is a description of the Brownells Oversized Tactical Bolt Knob.
This video segment is a description of the Accuracy International Rem. 700 AICS Detachable Magazines.
This video segment is a description of the Rifle Basix Remington 700 Rem-Saf Safety.
This video segment is a description of the Surgeon Rifles Short-Action Receiver & Bolt.
This video is a demonstration of the Williams Firearms Rem 700 and Win M70 Custom Steel Floorplate.
This video demonstrates how to properly clean your rifle or shotgun bore with JB Bore Paste, Kroil and VFG Pellets. This method should restore accuracy in fowled barrels and is used by top bench rest shooters.
A description of the Brownells Action Wrenches.
Lean how to install and properly remove the crimp in the magazine tube to increase the capacity of your Remington 870, 1187 or 1100 Special Field.
The Brownells/Tom Gresham HuntSavr kit was designed to enable the
average sportsman to make simple firearm repairs while in the field. While
it is impossible to provide solutions for every emergency, the HuntSavr kit
supplies solutions to some common problems that would otherwise render
the gun useless.
Some earlier model, centerfire Remington rifles have an extractor that
is riveted inside the face of the bolt. If the extractor breaks or fails, it must
be removed and new extractor and rivet installed.
This punch is designed to restore the swaged lip that keeps the magazine
cap detent ad spring in place in the 870 barrel guide ring. Reswaging of
this lip may be necessary after the gun has been used extensively and may
be necessary when reassembling an 870 if the detent was removed before
The 870’s Shell Latches, the 1100’s Feed Latch and Interceptor Latch
Spring, as well as the Shell Latches on older Model 58’s and 878’s, are held
in place by receiver metal which is swaged, or staked, against them.
The Brownells 870/1100 Carrier Pivot Slave Pin is designed to simplify
reassembly of the Fire Control Assembly (Trigger Group), by holding the
Carrier and Carrier Dog Washer in place while the Carrier Pivot Tube is
installed in the Trigger Plate.
The Kit consists of two, specially designed, hardened Riveting Punches
and the Cherry Corners 870 Ejector Spring Rivet Cutter. The #1 Punch,
identified by the small hole in its end, is made to secure the Ejector Spring
Housing to the inside of the shotgun receiver.
Based on factory proven design, the Brownells 870 Forend Wrench will
provide the user with the means of loosening even the tightest forend nuts
while minimizing the chance of damaging the forend wood or the nut itself.
The Trigger Plate Assembly (Remington calls it the Fire Control Unit) in
Remington 870, 1100 and 1187 shotguns is secured to the receiver by two
Trigger Plate Pins. These massive, solid pins are locked into the receiver by
strong detent springs.
The Remington 870/1100 shotgun’s buttstock is attached to the receiver
by a round head, slotted bolt. Use of a common screwdriver to loosen or
remove this stock bolt may deform the slot and cause severe damage to
The popular Remington 1100 and 11-87 semi-automatic shotguns utilize
an interceptor latch powered by a wire spring which is staked into the left
side of the receiver.
In the Remington 1100/11-87 semi-auto shotgun, the action bar sleeve
serves as a means of moving the action bar and bolt. Additionally, by virtue
of its size or mass, it also reduces the velocity, or speed, of the bolt as it moves
to the rear of the receiver.
The 870/1100 Magazine Spring Retainer Tool has been designed to
make installation of the Magazine Spring Retainer, used on the older
Remington 870/1100 12 gauge shotguns, simple and less hazardous.